{"id":82,"date":"2024-03-03T16:16:37","date_gmt":"2024-03-03T16:16:37","guid":{"rendered":"https:\/\/demosites.io\/pet-shop-gb\/?p=82"},"modified":"2024-07-30T05:44:50","modified_gmt":"2024-07-30T05:44:50","slug":"smart-dummy-led-load-module-slm","status":"publish","type":"post","link":"https:\/\/autoelectronicspart.com\/de\/2024\/03\/03\/smart-dummy-led-load-module-slm\/","title":{"rendered":"SMART LOAD MODULE FOR LED"},"content":{"rendered":"
<\/div>\n\n\n\n
<\/div>
\n
\n
<\/span>\"\"
\n

ELECTRONIC SMART MODULE FOR LOAD SIMULATION AND FAILURE CONTROL OF LED INDICATORS<\/strong><\/h2>\n<\/div><\/div>\n<\/div>\n<\/div><\/div>\n\n\n\n
<\/div>\n\n\n\n

OUR UNIVERSAL SMART DUMMY LED LOAD MODULE (SLM) SOLVES ALL THE PROBLEMS THAT OCCUR WHEN REPLACING A CONVENTIONAL LAMP WITH AN LED. <\/h4>\n\n\n\n

Electronic Smart Load Module (SLM)<\/a> Device solve LED Performance Issues with turning off all the way or flickering at specific dim levels and fix CAN BUS computer mistake.<\/strong><\/p>\n\n\n\n

<\/div>\n\n\n\n

WHY ARE INSTALLING LOAD RESISTORS FOR LED TURN SIGNAL LIGHTS?<\/h3>\n\n\n\n
<\/div>\n\n\n\n

If you don’t install load resistors with LED turn signal bulbs, after replacing incandescent light bulbs to LED, you will experience the notorious hyper flash issue. Hyper flash the turn signal light flashes rapidly. LED bulb have a very low current draw so when they are used on a after replacing incandescent light bulbs, they may flash faster than usual, as if there was a blown bulb, or not flash at all (if there\u2019s not enough \u2018resistance\u2019 to trigger the flasher relay)<\/p>\n\n\n\n

<\/p>\n\n\n\n

<\/div>\n\n\n\n

HOW MANY LED LOAD RESISTORS DO YOU NEED?<\/h3>\n\n\n\n

You will need 1 Load Resistor for each LED lamp installed. If you will have glass and LED bulbs on one vehicle, you DO NOT need to add a load resistor to any glass bulb, ONLY LED.
A load resistor is generally required for each LED\u2019s. To add a load resistor to an indicator (turn signal) it will need to be wired into each circuit in parallel and screw the load resistors to the radiator (vehicle body) so that the resistor does not burn out. The resistors can heat up to 170-180\u00b0 C.<\/p>\n\n\n\n

When you using our smart load module instead of a LED load resistor, the module SLM22112<\/a> (12 v) and SLM22124<\/a> (24 v) replaces 2 resistors with a capacity of 21 watts each, and the module SLM42124<\/a> (24 v) and SLM42112<\/a>(12 v)replaces 4 resistors with a capacity of 21 watts each. The module does not heat up and therefore does not require installation on a radiator.<\/p>\n\n\n\n

<\/div>\n\n\n\n

WHAT LOAD POWER IS NEEDED WHEN REPLACING TURN SIGNAL LAMPS WITH LEDS<\/h3>\n\n\n\n

When replacing a turn signal bulb with an LED, an additional 21 watt load is required. LED Dummy Load Resistors simulate a 21W globe in the circuit to rectify globe out messages & flash rate when using LED lights.<\/p>\n\n\n\n

<\/div>\n\n\n\n

PROBLEMS THAT THE SLM MODULE SOLVES<\/h3>\n\n\n\n
<\/div>\n\n\n\n

When incandescent light bulbs are replaced by LEDs in the headlights of the car, vehicle On-Board Computer generates error because that LEDs consume less power. Additional to this error, the frequency of the turn signal is increased. To correct operation of the On-Board Computer or to prevent incorrect work of relays, we have to simulate a load equal to incandescent bulbs. Usually used for this purpose \u201cLEDs load resistors\u201d and \u201cDummy resistors\u201c.
But those solutions have several serious disadvantages such as \u2013 inability of the On-Board Computer to detect LED\u2019s failure due to load resistor and the overheating of the load resistors.<\/p>\n\n\n\n

<\/div>\n\n\n\n

THE NOT HEATED SMART LOAD MODULE FOR LED (REPLACING STANDARD LOAD RESISTOR)<\/h3>\n\n\n\n

Usually when replacing ordinary lamps in cars with LEDs, used for this purpose \u201cLEDs load resistors\u201d or as they are also called \u201cDummy resistor\u201c.
But those solutions have several serious disadvantages such as – inability of the On-Board Computer to detect LED’s failure due to load resistor and the overheating of the load resistors.
Our company has developed an innovative intellectual module” that solved those problems!<\/p>\n\n\n\n

<\/div>\n\n\n\n

OUR DEVELOPMENT AND EXPERIENCE OF USE<\/h3>\n\n\n\n

Our smart module for LED indicators was developed through many years of experience supplying electronic devices to manufacturers and users of buses, coaches and trucks. Development was carried out in close collaboration with a major manufacturer of buses, taking into account the shortcomings of existing solutions on the market. Our module has been successfully used by bus manufacturers for over 10 years.<\/p>\n\n\n\n

<\/div>\n\n\n\n
<\/div>
\n
\n

SMART LOAD SPECIFICATION<\/h4>\n\n\n\n